Go to content Go to search
Attention Not all floors & accessories shown on this website are commercially available in every country. To check availability, please contact your local dealer. Not all floors & accessories shown on this website are commercially available in every country. To check availability, please contact your local dealer.


DIY vs. an installer:
the comparison

Found the hardwood floor of your dreams? Thanks to our Uniclic® (Multifit) click system, you can have it installed in no time, without any hassle. Roll up your sleeves or let an expert take care of the installation for you. The choice is yours.


  • Install the floor yourself with our convenient Uniclic (Multifit) click system
  • Compatible with floor heating
  • User-friendly installation instructions and videos at your disposal

Step-by-step guide


Don’t want to take any chances? Let an expert take care of your flooring project!

Find a Dealer

How to lay your own Quick-Step wooden floor

STEP 1: Choose your installation type: click or glued-down

Hardwood flooring can be installed one of two ways: clicked – also known as ‘floating installation’ – or glued-down. If you choose the click method, it is easier to replace individual planks when necessary, without damaging the rest of your wood floor. 

We advise you to always check the installation instructions for your floor and installation method before getting started.  

STEP 2: Prepare your subfloor

How you proceed depends on the type of subfloor you’re working with, so you’ll have to inspect it. We highly recommend working on a level, stable, and clean subfloor. Don’t forget to check for any loose parts – wood splinters, loose planks or tiles etc. 

How big can the joints in your existing tile floor be? How can you level out irregularities? Find out how to prepare your subfloor properly.

What about underfloor heating? Take your time to read the installation instructions so you are fully prepared to get started!

STEP 3: Choose your underlay or glue

Choosing the right underlay or glue – depending on you preferred installation method – is a crucial part of installing your brand-new hardwood flooring in a hassle-free way. 

Our specially designed Quick-Step underlays are damp-proof, insulating, noise-reducing, and self-levelling. Thanks to the smooth top surface, installing the wood floor and ensuring ample expansion afterwards is a piece of cake. 

Prefer to work with a glued-down installation? We’ve got you covered there too, with high-quality glue that’s sure to last you a lifetime and keep your hardwood floor in place.

STEP 4: Collect your tools

Want to save yourself a few trips to the hardware store and avoid other unnecessary interruptions during the installation? Make sure you have a couple of essential tools at hand before you get started.

A hammer and a saw are among the usual suspects, but there are several other tools that will make your life a lot easier.

STEP 5: Install your underlay

If you chose to install your hardwood floor using an underlay, it’s time to get started! If you prefer a glued-down installation, you can skip to step 6.

  • Roll out your underlay and push it as closely as possible against the wall. 
  • Lay one row at a time and make sure you go in the same direction as you plan to lay your floor (see step 6). 
  • Use the flap and glue strip for easy installation of the underlay with an integrated damp-resistant screen. When you cannot use the flap and strip, use an adhesive tape to attach the rows together in order to make the installation damp-proof. 

STEP 6: Laying your wooden floor

The following instructions are required for both glued-down and floating installation.

  1. First, check how many full rows of planks you will need by dividing the width of the room by the width of a plank.

  2. Make a mark on the wall where you’ll be laying your last full plank. The last plank should be at least 4 cm wide for easy installation.

  3. Unpack your planks and mix them up to avoid adjacent identical patterns and colour variations.

  4. For an optimal result, start laying your first row of hardwood planks in line with the longest wall, but do not flush against it (as walls are hardly ever perfectly straight).

  5. Make sure to alternate your alignment so that end joints of successive rows are never in line. We recommend leaving at least 30 cm between them.

  6. Click the first plank of the second row into the first plank of the first row (see video) and keep going like that.

STEP 7: Saw your wooden floor

It’s heart-breaking, but there’s no way around it: you will have to saw your hardwood floor to make sure it fits your space perfectly. But don’t worry! We’ll show you exactly how to do it, and you’ll be blown away by the result.

Wear gloves and use a pencil to draw your cutting lines. Always saw your planks with the top surface decoration facing upwards.

STEP 8: Finish your wooden floor in style

With your hardwood floor in place, you’re almost there! Now it’s time to complete the picture with matching skirting boards, finishing profiles, and other fine touches. After all, it’s all in the details.

Still got questions?

Need help finishing your project to your satisfaction?
Take a look at our help centre, which contains answers to the most frequently asked questions!

Go to our help centre